翻板閥、鎖風閥、卸灰閥類
氣動鐘形卸灰閥

本系列鐘形卸灰閥廣泛適用于冶金、建材、石化、電力等行業,作為各工業爐窯及除塵系統的卸灰裝置。

This series valve is widely used in metallurgy, building material, oil chemical and electric power industries etc. It is the discharging device of stove and removing dust system.

 

結構特點:

Structure characteristic:

該鐘形卸灰閥由閥體、錐形閥塞、連桿、驅動裝置等組成,用連桿拉動閥塞上下運動完成啟閉動作。其中X型為橡膠軟密封,應用于冶煉高爐噴煤系統的煤粉輸送控制。W型為閥體本體材料密封,應用于除塵系統塵灰輸送控制。

This valve is made up of body, cone valve plug, connected pole, driving device etc. The plug drew by the connected pole moves up and down to complete the action of open and close. Type X denotes rubber soft seal, which is applied to carrying control of coal powder in smelt blast furnace gushing coal system. Type W denotes body material seal, which is applied to carrying control of dust powder in removing dust system.

 

性能參數:

Performance parameter:

公稱壓力

Nominal pressure

0.4MPa

適用溫度

Suitable temperature

80150

密封試驗壓力

Seal test pressure

0.44MPa

強度試驗壓力

Strength test pressure

0.6MPa

適用介質

Suitable medium

含煤氣塵灰、煙氣塵灰煤粉等干燥細粉物料

Dust with coal gas and smoke, dry powder

 

工作原理:

Working principle:

手動鐘形卸灰閥利用力矩平衡的方法實現卸灰。當作用于錐形塞上的物料產生的力矩大于重錘搖桿產生的力矩時,錐形塞打開向下卸灰。一旦積灰卸去后,重錘與搖桿產生的力矩使錐形塞迅速關閥。落料的頻率及卸灰量依據工況需要來調整重錘位置。

執行機構得到程序指令后推動搖桿使錐形塞打開向下卸灰,積灰卸去后,依據程序規定時間,推桿推進使錐形塞關閉密閉。執行機構的推出與推進都有行程控制,同時反饋開關信號。

The valve realizes discharging using trimming moment. When the moment made by material on cone plug is greater than that of heavy hammer and rocker, the plug will open adown to discharge. After discharge the moment made by heavy hammer and rocker will drive cone plug close quickly. Dropping material frequency and discharge amount is determined by the working condition demand to adjust heavy hammer position.

Actuator drives the rocker after receives program order, and the rocker drives the plug open adown to discharge dust. Draw stem drives the plug to close according to the program time after discharge. Push and extrusion of actuator are controlled by journey and feed back switch signal at the same time.

XH--- X W系列外形連接尺寸:

Appearance joint dimension:

DN

200

250

300

350

400

450

500

600

700

800

D

370

420

480

530

620

670

720

835

935

1055

D1

330

380

440

490

570

620

670

780

880

990

D2

280

330

380

430

500

550

600

700

800

900

D3

390

440

500

550

650

700

750

865

965

1083

D4

350

400

460

510

600

650

700

810

910

1020

D5

240

290

340

390

450

500

550

650

750

850

H

350

400

450

500

550

600

640

680

730

760

H1

480

530

580

630

680

730

770

810

860

890

L1

755

805

855

925

975

1025

1075

1275

1375

1475

L2

740

790

840

910

960

1010

1060

1200

1300

1400

n-d

8-Φ18

12-Φ18

12-Φ22

12-Φ22

16-Φ22

16-Φ22

20-Φ22

20-Φ26

24-Φ26

24-Φ30

電動推桿

Electric draw stem

DTA25-M

P0.025kw

DTA63-M

P0.06kw

DTA100-M

P0.25kw

氣動推桿

Pneumatic   draw stem

10A-5TCC32B

10A-5TCC40B

10A-5TCC50B

 

使用說明:

Operation instruction:

l  安裝時請注意閘門本體上標明介質流向,清除內腔附著物。兩法蘭連接時必須加密封墊片,然后均勻鎖緊螺栓。

l  設備在運行時,請定期給傳動部分加潤滑油。執行部分定期維護和檢修。

l  若長期存放應使設備處于關閉狀態,各傳動部位加潤滑油,不允許露天存放或堆置。

l   Pay attention to the direction of medium in valve body. Clean the inner body. Add seal cushion between two flanges connection and screw down bolt

l   Please add lubricant to transmission when equipment is operating and maintain and check the actuator regularly.

l   Add lubricant to transmission part when valve is long stored. It should not be placed or piled up in the open air.


湖北澳星環保成套設備有限公司 版權所有

備案號: 鄂ICP備14001966號-1

地址:湖北省荊州市沙市區十號路98號 電話:0716-4302555 傳真:0716-4310988